0.08 voltage case then falls back to 0 (the drop)
1. Download samsung s3 boot card click here
2. Extract the file on the desktop or the folder itself
3. Prepare and enter MMC card reader / 2Gb Sd card (tested) to connect to a PC to create a boot file
4. Then look at the Boot patch files in the download folder first before Diskdump2.exe
5. Select that for generic storage Memory Card
6. Then see he will write the script bot into MMC via CMD s3 boot loader before
succesfully created Dead boot memorycard
1. Download samsung s3 boot card click here
2. Extract the file on the desktop or the folder itself
3. Prepare and enter MMC card reader / 2Gb Sd card (tested) to connect to a PC to create a boot file
4. Then look at the Boot patch files in the download folder first before Diskdump2.exe
5. Select that for generic storage Memory Card
6. Then see he will write the script bot into MMC via CMD s3 boot loader before
succesfully created Dead boot memorycard
1. input mmc
2. run tempro.exe
3. Select the serial >> port: com32: USB serial port (com32)
4. setup> serial port> fox baud rate to 115200
5. connect octopus (rj45 com / usb serial port com32)6.connect to phone> battery input
Next Step
Use free tool for flashing while relaxing first :
> Samsung Z3X Box / SPT Box (I use z3x box for interfaces, may medusa / octopus)
> Special cable UART (300k or 500k)
> Download teraterm-4.78 From teratrem-4.78
> Keep the battery condition FULL
Dead boot repair execution procedure read it :
* Download and extract TeraTerm-4.78 in the desktop / folder itself
* From the folder you extracted in ttermpro.exe CLICK continues there is no serial port option and change the serial com port via serial z3x
* After the selected serial port and press Ok continue Button / Setup tab click Serial Port Option
select Baud Rate 115200 select Ok
select Baud Rate 115200 select Ok
* And select the SD card / MMC reply has been made earlier to the Phone boot that we maau execution
* Plug Cable UART via z3x box
* The input battery approximate 5 minute wait if this process (not finished try again repeated the initial step of uart cable enter the memory and then the battery)
LOG successful if its like this :
pit_check_integrity: invalid pit.(0x0)pit_check_integrity: invalid pit.(0x0)
update_guid_partition_table: There is no pit binary.
fsd_reclaim 1283: MST is not recognized(mst.magic=0x0)
fsd_reclaim 1284: MST is not recognized
fsd_reclaim 1599: Error(nErr=0x0)
fsd_reclaim 1604: j4fs_rw_start is set to default value(128KB)
j4fs_open 153: Error(nErr=0x40000000)
j4fs_read_file_bootloader 355: j4fs panic
load_j4fs_param: 'param.j4fs' does not exist, make new one..
j4fs_write_file_bootloader 184: j4fs panic
fail
j4fs_read_file_bootloader 355: j4fs panic
load_j4fs_param: debug level file does not exist..*INCORRECT!*
init_fuel_gauge: battery is not detected, do not init fuelgauge
init_microusb_ic: MUIC: CONTROL1:0x1b
init_microusb_ic: MUIC: CONTROL1:0x1b
init_microusb_ic: MUIC: CONTROL2:0x3b
init_microusb_ic: MUIC: CONTROL2:0x3a
PMIC_ID = 0x2
PMIC_IRQSRC = 0x0
PMIC_STATUS1 = 0x10
PMIC_STATUS2 = 0x0
PMIC_PWRON = 0x2
PMIC_IRQ1 = 0x27
PMIC_IRQ2 = 0x0
s5p_check_keypad: keypad value=0x0
s5p_check_reboot_mode: INFORM3 = 0 ... skip
s5p_check_upload: MAGIC CODE=d1b0f038
microusb_get_attached_device: STATUS1:0x3c, 2:0x0
s5p_check_download: update mode=0
j4fs_read_file_bootloader 355: j4fs panic
s5p_check_tzsw: invalid tzsw type! dummy?
scr_draw_image: draw 'download_error.jpg'...
j4fs_read_file_bootloader 355: j4fs panic
read_param_file: 'download_error.jpg' j4fs read failed!
fimd_div:13, div:1, FB_SOURCE_CLOCK:800000000, FB_PIXEL_CLOCK:57153600
a2, 60, 90,done
If the log below [Patch Stop] This is not a Rom Code. try to replace the MMC / SD card first if it fails kept meaning EMMC damaged box must be in dirrect via jtag, It LOG if the error continues ....
TN default[DVFS] INT(1) : 0
DRAM Type : LPDDR2 8G
[DVFS] MIF(3) : 0
[EPLL][VPLL][CLK_DIV] OK
[LOCK SW/HW]ARM:0/0 INT:0/0 G3D:0/0 MIF:0/0 SHIFT:0/0
[DVFS] ARM(0) : 5
[DVFS] INT(1) : 0
[DVFS] G3D(2) : 0
[DVFS] MIF(3) : 0
[SD_INIT
SDMMC_HighSpeedONE]
SD_READ: 20000 20000 0x40008000 -> 668484 usec
Inp32(uAddr) : 0xea00007e
FW Booting
[Patch Stop] This is not Rom Code.Such cases are usually broken her EMMC
If he is usually done directly blank white or line screen.
Leave blank white condition try to plug the usb jig or to downlode mode then try to see if the opposite jgn hpnya off immediately flash use Odin.
continue to try in ODIN or use flashing box via file PIT try his file that is broken there is no reply .md5 csc etc.
try searching for the file repair EFSbecause the IMEI is 004999010640000 googling null as many who shared
I9300_Repair_efs.tar.rar
I9300_Repair_efs.tar.rar
if there is a shortage please straightened
Komentar
Posting Komentar